Forums
New posts
Search forums
What's new
New posts
New media
New media comments
New profile posts
Latest activity
Media
New media
New comments
Search media
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Install the app
Install
Forums
Multimedia & Entertainment
Build Ups & Projects
ReplicaR's Mustang build *finally on track again*
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="ReplicaR" data-source="post: 1417850" data-attributes="member: 9209"><p>So, yesterday I spent about 5 hours working on the mustang. The work consisted of resealing the diff cover, and reinstalling the dampers. The cover was my fault. I didn't use a gasket, and didn't seal the cover well enough, and surely, it leaked. This time I sealed the diff cover with a gasket, and put the Ultra Black on both sides, so hopefully this does it. I'll check back again in a couple of days to make sure that there are no leaks. I used similar procedure for thermostat, and no leaks there with thinner fluid and under pressure.</p><p></p><p>The shock install was pretty time consuming. I had to trim down the bushings in the rear shocks, so I could even mount the damn thing, put the rear coilovers on, take them off realizing that shortening the body meant that I had to adjust the ring, putting them on again, taking them off one more time, because the rear was too low still, install front ones, mount all the wheels, lower the car, raise the car, adjust front left, and finish. Definitely not my favorite task as far as installation goes. The rear coilover sleeves spin freely on the shock, so that means you have to hold the sleeve in place with something, and the right side has no room to work on between the panhard rod and rear exit exhaust, so taking the shocks off was honestly, the fastest way to adjust them. Anyway... done venting.</p><p></p><p>The impressions: The damper rebuild made a huge difference in how the car feels. Even at full soft settings, I can tell the shocks are much firmer than they used to be previously. I tried it just around a few slow corners, over some slow bumps, and quick direction changes. Even at full stiff on the original dampers, the car felt a little floppy. It was firm, but it didn't feel controlled. That's definitely not the case anymore. The body motion feels controlled and smooth, it doesn't flop around like it used to. The car feels much more composed, doesn't feel like the rear axle acts as freeweight anymore, just bouncing around at its own will. I am very much looking to see just how confidence inspiring the car will be at the track. More updates to come. No pictures, because I was in a rush to finish it.</p></blockquote><p></p>
[QUOTE="ReplicaR, post: 1417850, member: 9209"] So, yesterday I spent about 5 hours working on the mustang. The work consisted of resealing the diff cover, and reinstalling the dampers. The cover was my fault. I didn't use a gasket, and didn't seal the cover well enough, and surely, it leaked. This time I sealed the diff cover with a gasket, and put the Ultra Black on both sides, so hopefully this does it. I'll check back again in a couple of days to make sure that there are no leaks. I used similar procedure for thermostat, and no leaks there with thinner fluid and under pressure. The shock install was pretty time consuming. I had to trim down the bushings in the rear shocks, so I could even mount the damn thing, put the rear coilovers on, take them off realizing that shortening the body meant that I had to adjust the ring, putting them on again, taking them off one more time, because the rear was too low still, install front ones, mount all the wheels, lower the car, raise the car, adjust front left, and finish. Definitely not my favorite task as far as installation goes. The rear coilover sleeves spin freely on the shock, so that means you have to hold the sleeve in place with something, and the right side has no room to work on between the panhard rod and rear exit exhaust, so taking the shocks off was honestly, the fastest way to adjust them. Anyway... done venting. The impressions: The damper rebuild made a huge difference in how the car feels. Even at full soft settings, I can tell the shocks are much firmer than they used to be previously. I tried it just around a few slow corners, over some slow bumps, and quick direction changes. Even at full stiff on the original dampers, the car felt a little floppy. It was firm, but it didn't feel controlled. That's definitely not the case anymore. The body motion feels controlled and smooth, it doesn't flop around like it used to. The car feels much more composed, doesn't feel like the rear axle acts as freeweight anymore, just bouncing around at its own will. I am very much looking to see just how confidence inspiring the car will be at the track. More updates to come. No pictures, because I was in a rush to finish it. [/QUOTE]
Insert quotes…
Verification
Post reply
Random media
Latest posts
Short to ground
Latest: cobrajeff96
Today at 1:48 AM
Electrical & Stereo
BBK VALVE COVERS
Latest: 07GtS197
Yesterday at 11:13 PM
General Tech
Valve covers
Latest: ttocs
Yesterday at 3:54 PM
Community News
Bluetooth transmitter- any that power off plugged in?
Latest: 07GtS197
Yesterday at 3:09 PM
Electrical & Stereo
Weird sensor
Latest: 07GtS197
Yesterday at 3:07 PM
General Tech
Share this page
Reddit
Pinterest
Tumblr
WhatsApp
Email
Share
Link
Forum statistics
Threads
78,611
Messages
1,537,415
Members
16,253
Latest member
STITCHSCREWW
Members online
TTSaleen
Forums
Multimedia & Entertainment
Build Ups & Projects
ReplicaR's Mustang build *finally on track again*
Top