ttocs
Post Whore
and I got a set that were used just long enough to realize I needed a tad bigger. $100
1995 mustang build up :D
- Thread starter 1994stangfan
- Start date
OP
OP
1994stangfan
Active Member
1995 mustang build up
One more picture because.... uhmmm it’s beautiful
One more picture because.... uhmmm it’s beautiful
OP
OP
1994stangfan
Active Member
New 42 lb injectors showed up 
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
OP
OP
1994stangfan
Active Member
Heads are cleaned and painted. Looking beautiful
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Very nice
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
OP
OP
1994stangfan
Active Member
1995 mustang build up
Some parts arrived
Sent from my iPhone using Tapatalk
Some parts arrived
Sent from my iPhone using Tapatalk
This is going to be a clean install!
OP
OP
1994stangfan
Active Member
1995 mustang build up
Picked these up today. Going to strip the paint and polish them. May need to clearance them for my roller rockers. Is anyone running cobra 1.7 with fox valve covers?
Also painted my gt40 heads
Sent from my iPhone using Tapatalk
Picked these up today. Going to strip the paint and polish them. May need to clearance them for my roller rockers. Is anyone running cobra 1.7 with fox valve covers?
Also painted my gt40 heads
Sent from my iPhone using Tapatalk
I’m not running fox covers.........actually I ain’t running anything right now....... but several others are. I do believe that’s what Ttocs is running on his.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
ttocs
Post Whore
I am running 1.6's with mine but I did shave down the baffle inside to make sure there was enough room as from what I read it was needed.
OP
OP
1994stangfan
Active Member
Thanks for the reply. Do you have any pictures?
On a different note, project will be delayed for a few months now. Have to save for a cam or find a cheap low mileage used one (not likely lol)
Sent from my iPhone using Tapatalk
ttocs
Post Whore
pics of the bottom that I trimmed? No sorry it was not a photoworthy job since no one sees it but look on the bottom and where the baffle is mounted just try to trim it down as flat as possible
What are you calling cheap for a cam? Shelf cans are reasonably cheap and custom grinds aren’t much either. Luckily we only have to buy one cam so they are very easy to get.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
OP
OP
1994stangfan
Active Member
Progress
After stripping and washing
After first step of sanding 220 grit
Long way to go, all the way to 2000grit
Sent from my iPhone using Tapatalk
After stripping and washing
After first step of sanding 220 grit
Long way to go, all the way to 2000grit
Sent from my iPhone using Tapatalk
OP
OP
1994stangfan
Active Member
Gettting there...
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
OP
OP
1994stangfan
Active Member
More pieces to the puzzle
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
OP
OP
1994stangfan
Active Member
Started porting my gt40 lower today. It’s going pretty well. Have a lot way to go yet, but there is something really mystical about knowing you’re creating power for free
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Was you motor boating sounds the whole time? Cause i would've been!
OP
OP
1994stangfan
Active Member
Not this time, but you’ve given me ideas now lol
Sent from my iPhone using Tapatalk
OP
OP
1994stangfan
Active Member
Progress
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
