clark98gt
Active Member
You dont need any adapters of any sort to swap a pi intake on npi heads, just a dab of silicone. I know because I have it.
FRANKENSTANG's NEW CAR !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
- Thread starter FrankenStang
- Start date
- Status
OP
OP
FrankenStang
Well-Known Member
no adpaters needed...just use pi gaskets..they in no way hinder any airpath what so ever...like clark said, just some rtv in 2 coolant ports and ur good togo...
My swap was a success. i havent really been able to get on it yet as the longer i wait the better..but its 0-30 was about the same but after that in the high rpm's you can feel the pi breathe..and at wot when my car shifts it bounces the rev limiter abit because the stock tune cant correct for the higher stall tc i have..so a few more mods, a tune and then just get the car looking good and clean..bodywork will be last..
My swap was a success. i havent really been able to get on it yet as the longer i wait the better..but its 0-30 was about the same but after that in the high rpm's you can feel the pi breathe..and at wot when my car shifts it bounces the rev limiter abit because the stock tune cant correct for the higher stall tc i have..so a few more mods, a tune and then just get the car looking good and clean..bodywork will be last..
Nightmare
Well-Known Member
goes to show you the reliability of the intetnet.
OP
OP
FrankenStang
Well-Known Member
heyyyy cedarburg huh....my Gma used to have a candyshop downtown there...
Nightmare
Well-Known Member
that's cool. In downtown?
OP
OP
FrankenStang
Well-Known Member
ya.....was called Maryjanes ( lol )
MustangChris
Mythic Level
lol.
OP
OP
FrankenStang
Well-Known Member
heres pics of the progress, she runs WAYY better and WOW,lol didnt think a few bolton would make that big of a deal...im getting my 24lb injects cleaned and will install them soon..so now the cars mods are, built 4r70 trans, 2800 stall tc, 1 piece aluminum drive shaft, slotted and drilled rotors with hawk pads,2.5 in xpiped exhaust with 6in bolrla's, msd wires 180 degree thermostat, 2002 gt intake system from plenum to mafs..now once i sell my extra parts i wanna buiy a 78mm bbk 1 piece Tbody/plenum combo,high output alternator, install my pi cams and get a custom tune or the same tuner superchips tuner i had on my cougar..and then call it a day untill i can afford a supercharger! so it will be a real supercoupe again,since now all my boost guage reads is vacuum 
OP
OP
FrankenStang
Well-Known Member
lol, ya i found a mouse house on the Tbirds block...
KidK9
Well-Known Member
I don't know how you get yourself into these situations....
OP
OP
FrankenStang
Well-Known Member
went very well, as you can tell even the oil filler stayed in its spot the whole time...!
KidK9
Well-Known Member
Oh I just meant that only you could find a darn mouse nest on your block!!
OP
OP
FrankenStang
Well-Known Member
nice 1st test coming for the car...7 hour each way drive coming up...fresh oil should help her and lets see if them pi parts did better or worse for gas mileage..
KidK9
Well-Known Member
Yes, really.
The rodent that #occupymy05GT chewed thru a few of the wires while he was at it and led to a set of charge motion delete plates..
Nightmare
Well-Known Member
So why are you selling it now? Came apon it browsing cl.
the.greg
Well-Known Member
Ive also pulled a dead mouse and mouse nest out off a car's engine bay before. It happens
MustangChris
Mythic Level
wow. lol. good stuff!
- Status
