going to the dyno

[Blk97GT]

I wanna get an idea of what you guys think my car will lay down on the dyno. Want some other people thoughts so I dont over estimate and then wind up dissapointed :angry7: car will be on a dynojet frist weekend of may. here are my mods

1997 Mustang GT
Mods:
2004 PI motor
UPR plenum
FRPP 70mm TB
UPR intake
plenum spacer
UPR underdrive pulleys(Alt & water pump)
March SFI fluid dampner crank pulley
Mac catback
High flow catted H
Accel coil packs
Superchips 93 octane tune

Not power makers but may help
centerforce DF clutch
Fidanza AL flywheel
3.55 gears

 

[mygreengt]

im gonna guess aound 250 or 260.. who knows could be more

 

[NASTY03GT]

hmmm, I will guess 255-265.

 

[adrift]

I wanna get an idea of what you guys think my car will lay down on the dyno. Want some other people thoughts so I dont over estimate and then wind up dissapointed :angry7: car will be on a dynojet frist weekend of may. here are my mods

1997 Mustang GT
Mods:
2004 PI motor
UPR plenum
FRPP 70mm TB
UPR intake
plenum spacer
UPR underdrive pulleys(Alt & water pump)
March SFI fluid dampner crank pulley
Mac catback
High flow catted H
Accel coil packs
Superchips 93 octane tune

Not power makers but may help
centerforce DF clutch
Fidanza AL flywheel
3.55 gears

If you don't mind me asking, where did you get the high flow catted H?

 

[Lee12609]

what kind of dyno?

 

[duff daddy]

screw the dyno, get me et #'s after its tuned right!!!

 

[Blk97GT]

what kind of dyno?

dynojet

 

[Blk97GT]

I wanna get an idea of what you guys think my car will lay down on the dyno. Want some other people thoughts so I dont over estimate and then wind up dissapointed :angry7: car will be on a dynojet frist weekend of may. here are my mods

1997 Mustang GT
Mods:
2004 PI motor
UPR plenum
FRPP 70mm TB
UPR intake
plenum spacer
UPR underdrive pulleys(Alt & water pump)
March SFI fluid dampner crank pulley
Mac catback
High flow catted H
Accel coil packs
Superchips 93 octane tune

Not power makers but may help
centerforce DF clutch
Fidanza AL flywheel
3.55 gears

If you don't mind me asking, where did you get the high flow catted H?

That and the catback were on the car when I got it, everything else I have done so I dont even know what brand it is.

 

[Lee12609]

i'm gonna say anywhere from 240-265, depends on that superchip tune, LOL.....

 

[MustangChris]

$1.00 bob.









im guessing 245

 

[pp_puncher]

Want some other people thoughts so I dont over estimate and then wind up dissapointed :angry7:

320RWHP..... hope you're not dissapointed LOL

 

[sanchezcruz_20]

about 210 rwhp for the 04 motor ( bout 20% loss, auto or stick?)
approx , maybe 30 for all your bolt ons, but thats crank power again...the exhaust and the tune being a large majority of that ...freeing up some HP,

240rwhp, bob.....(there is no method to my madness, just a guess)

 

[LI98GT]

With the mods you have listed on the PI motor, should be about 250rwhp give or take. Good luck on the numbers and nice list of mods you have there.

 

[KWClutch]

243hp/251 lbft.

 

[98GTnSC]

ima say around 250-260. depending on the tune

 

[mygreengt]

any updates???

 

[Lee12609]

243hp/251 lbft.

4v torque numbers, LOL.......

 

[KWClutch]

I know. I was just making him feel good. lol

 

[Blk97GT]

any updates???

Dyno day is may 8th, ill be sure to post the results.

 

[NXcoupe]

$1.00 bob.









im guessing 245

And you'd be right. It will be in the 245 to 250 range. That's assuming it has a fantastic tune on it. I have done a lot of these 4.6's and with those mods, that's the general area they fall into. Unless the guy that owns the dyno has fudged the calculations, then hell, you could make 300 rwhp lol.