Well.....are you done yet? Eager to hear it run.
School me on my new 2v!
- Thread starter SN90FiveOh
- Start date
SN90FiveOh
Active Member
Haha no not yet. I still need to get a clutch fork, pivot ball, and engine mounts.
Sent from my SM-G920V using Tapatalk
You should beat the water pump nipple out of the block and install the new one to combat that pesky leak you had before.
SN90FiveOh
Active Member
Ok so I did more work today. Its starting to look like an engine!
It started getting dark out and the mosquito's were killing me so I torqued the timing cover and called it a night.
Sent from my SM-G920V using Tapatalk
It started getting dark out and the mosquito's were killing me so I torqued the timing cover and called it a night.
Sent from my SM-G920V using Tapatalk
SN90FiveOh
Active Member
Here are some pictures that I thought [MENTION=20210]lwarrior1016[/MENTION] and [MENTION=14727]96blak54[/MENTION] would Like to see. You can see how much the heads sit lower than the timing cover.
Luckily the bolt holes in the timing cover are much bigger than the bolts so there was no binding problem. The bolts are just off centered.
Sent from my SM-G920V using Tapatalk
Luckily the bolt holes in the timing cover are much bigger than the bolts so there was no binding problem. The bolts are just off centered.
Sent from my SM-G920V using Tapatalk
Thats not too bad. Nice to see a comparison so everyone knows what they will need to do after their heads get decked.
SN90FiveOh
Active Member
Finished putting the engine together today. Got a new heater nipple, clutch fork, and pivot ball.
Put my valve covers, oil pan, oil filter adapter, and headers on.
Sent from my SM-G920V using Tapatalk
Put my valve covers, oil pan, oil filter adapter, and headers on.
Sent from my SM-G920V using Tapatalk
A brand new gasket should cover that amount fine. Heck, stock gasket probably be ok. How well did it seal up
SN90FiveOh
Active Member
It looked like it had no problem filling that gap. Especially since that's the spot where you already have to put silicone.
Sent from my SM-G920V using Tapatalk
BAM!...There you go!
SN90FiveOh
Active Member
Look like my longtubes will clear this? Or cut more?
Sent from my SM-G920V using Tapatalk
SN90FiveOh
Active Member
Just an FYI this was not enough taken out. I ended up pulling the passenger header anyway. The engine is in the car as of last night.
Sent from my SM-G920V using Tapatalk
Sent from my SM-G920V using Tapatalk
Sn95 and headers......pisses me off thinking about it.
What headers are you trying to use?
What headers are you trying to use?
blackdemon007
Active Member
I think it's easier to just pull everything out, than it is to put that longtube on in the car
Sent from my SM-G925T using Tapatalk
Sent from my SM-G925T using Tapatalk
SN90FiveOh
Active Member
I have bbk longtubes [MENTION=14727]96blak54[/MENTION]
I have a tubular k member. Its not so bad. [MENTION=18797]blackdemon007[/MENTION]
Sent from my SM-G920V using Tapatalk
blackdemon007
Active Member
Yeah I guess that would help. Still on my list of parts to get
Sent from my SM-G925T using Tapatalk
Sent from my SM-G925T using Tapatalk
I wish headers would fit for me. I envisioned headers while bolting the exhaust up today. I cant see how its possible. There is no room. Guess ill stick with shorties!
SN90FiveOh
Active Member
SN90FiveOh
Active Member
My old custom tune with the timing pulled out after a warm up
https://youtu.be/2F46DkeLjW4
Sent from my SM-G920V using Tapatalk
https://youtu.be/2F46DkeLjW4
Sent from my SM-G920V using Tapatalk
SN90FiveOh
Active Member
Thanks [MENTION=14727]96blak54[/MENTION] and [MENTION=20210]lwarrior1016[/MENTION] for all of the help and support!
Sent from my SM-G920V using Tapatalk
Sent from my SM-G920V using Tapatalk
