What Did You Do To Your Car Today?

[RAU03MACH]

To day no progress
I'll get some done tomorrow morning
Mostly wire harness knock sencors
The injector harness and vacuum lines
Then I should be able to drop the engine in the car

 

[white95]

Installed the new rear sway bar in my truck.

 

[RAU03MACH]

I did get the injector harness hooked up along with a new vacuum line assembly
Modified my knock sencors installed
If its not windy with dust I will get this engine in

 

[oilspill]

Installed New rear lower control arms

Sent from my iPhone using Tapatalk

 

[dwcopple]

Fingers up!View attachment 10302

Sent from my SM-A102U using Tapatalk

You should paint your calipers IMHO

 

[ttocs]

Today I cut that piece of the trans tunnel out. Tomorrow hopefully I can finally mount the t56, measure the driveshaft/start to put the exhaust back together....

 

[Butchman205]

https://share.icloud.com/photos/00Uyvlr4-Bt-CSJQxQI5YpPjA

I’ve been tuning on my ‘95 Mustang GT.
With very much effort, I found the “sweet spot”. Man that sucker jumps from 2k-7k rpm VERY quickly. (Can’t wait to get it on the track and see how he runs!)

 

[Randall Garner]

Brought home a new project. Been sitting a few years. 1998 GT Convertible.

 

[RAU03MACH]

Nothing today and yesterday
The wind and dust are bad
I'm going to try next week

 

[ttocs]

I reinstalled the trans today, only to discover its still hitting the area right in front of the shifter even after cutting a section out. I think or hope I have the wrong cross member at this point or I am not sure how much more I can clearance.

 

[RAU03MACH]

I reinstalled the trans today, only to discover its still hitting the area right in front of the shifter even after cutting a section out. I think or hope I have the wrong cross member at this point or I am not sure how much more I can clearance.

Do you have picture of where its hitting and the clearance
I have heard those transmissions go in fairly easy
But I guess you don't until you experience it

 

[joe65]

Installed the new rear sway bar in my truck.

View attachment 10306

whoa you jacked it up by the diff....i remember a conversation about that i while back......

 

[joe65]

I'm a little late on this but it was Saturday. First "official" cars n coffee here since the pandemic started. shit ton of people showed up. must have been 400 hundred cars at least. this is just a sample. must have been 6 mclarens, 2 Ford Gt's, countless Porsches. The fox was for sale, it was really nicely painted. Having the car sit out next to other highly detailed cars made me realize how bad my headlights are, so i came home and ordered a new set.

 

[RAU03MACH]

whoa you jacked it up by the diff....i remember a conversation about that i while back......

Good catch we were ridiculed for doing that
it was like a 12 page write up

 

[white95]

whoa you jacked it up by the diff....i remember a conversation about that i while back......

No, the truck was on jack stands off camera. I lifted the rear end to “load the suspension” before tightening the axle brackets.

 

[white95]

Good catch we were ridiculed for doing that
it was like a 12 page write up

I didn’t post in the thread for a reason.

 

[DKblue98GT]

Yesterday: Drove the Cobra and Tacoma long enough to warm them up and changed oil and filter in both.

 

[RAU03MACH]

I didn’t post in the thread for a reason.

Its all good

 

[Blueraz_5.0]

Yesterday I discovered I had a blown head gasket. So I drained my bank account for this car and began the painful progress of ripping into my engine.

 

[96laseredcobra]

You should paint your calipers IMHO

I plan on blacking them out asap.

Sent from my SM-A102U using Tapatalk