OP
OP
Coming soon...
White's '95 GT "Unicorn"
- Thread starter white95
- Start date
OP
OP
really like the ECU mounted here instead of on the passenger floor board.
Thankfully I was able to reinstall the HVAC duct because God knows we can’t live without AC in Louisiana
Thankfully I was able to reinstall the HVAC duct because God knows we can’t live without AC in Louisiana
ElrodKTPQ_89
Legend
In Arkanslaw we burn up like real men (idiots)
OP
OP
Such a cluster fuck!
ttocs
Post Whore
lol its only just begun.....
OP
OP
Oh yes. I still have to figure out gauges!!
Currently, I’m building the harness to connect the hvac, fuel pump and engine fan to my Leash relay box. Decided to mount said relay box in the trunk near the battery and run the output wiring forward.
I’m at a stand still with the battery relocation while waiting for a 200A circuit breaker to arrive. They’re available locally but marked up about $30 so. No.
OP
OP
ALMOST looks like a car again!
DKblue98GT
Well-Known Member
- Joined
- Dec 19, 2009
- Messages
- 1,406
- Reaction score
- 333
Fenders at last...
OP
OP
Not much to show but the Holley ECU is mostly wired into the power system. All that remains is wiring up my relay box for fuel, engine fan and the hvac.
I am beyond excited to finally hear this MFer run!
I am beyond excited to finally hear this MFer run!
OP
OP
I'm going to pick up some bulkhead fittings and a 200A circuit breaker to finalize my battery relocation. This is roughly what I'm going to do. I'm going to use the bulkhead fittings on the actual box to make adding a kill switch simple later. Also, it will give me an external connection point to keep unnecessary wiring out of the box.
OP
OP
This is what I did to relocate my battery. I will add in a battery cut off switch later. Also, I didn't draw where the power harness is ground on the driver's side frame rail.
Do you not have a ground going to the frame close to the battery as well?
Sent from my iPhone using Tapatalk
OP
OP
Haven’t finished the trunk section yet but yes, it will. The drawing will reflect a lot more wiring as it’s completed.
OP
OP
Installed my new retro fit headlights and HID kit from @B.mad over at Madd Retros!! More information on these can be found here:
https://www.instagram.com/p/BwX0eA2BhNm/?utm_source=ig_share_sheet&igshid=15qu7txcuq7pa
OP
OP
Preliminary roll bar installation SUCKS!! It’s going to come back out to be welded and painted.
Good, good. Go slow, it is a PITA but worth the time and extra stiffness.
I was soaked with sweat by the time I got mine in. Then I welded the underside to the top side and made a nice jack point here to lift the car by tying into the long bar on the sub frame connectors. A lot of effort and all I get is grief for the shitty welds..
I was soaked with sweat by the time I got mine in. Then I welded the underside to the top side and made a nice jack point here to lift the car by tying into the long bar on the sub frame connectors. A lot of effort and all I get is grief for the shitty welds..
OP
OP
The car went for a leisurely trip to the day spa but will return with the rest of the MM suspension welded up and the built rear end swapped in.
ttocs
Post Whore
did someone say M&M?!
drink......
drink......
OP
OP
Sipping on some bourbon cream on ice as we speak...........
And by sipping I basically sip down a rocks glass in one gulp..........
Sent from my iPhone using Tapatalk
And by sipping I basically sip down a rocks glass in one gulp..........
Sent from my iPhone using Tapatalk
Similar threads
